Congratulations on your purchase of the Seamax Boat Cover, one of the best methods of protecting your inflatable boat from elements is with a well-designed and good quality cover. Covering the boat from sun damage and oxidation prevents dirt from setting on the interior and exterior and keeps moisture from causing mildew or rot to the surfaces. A nice boat cover is always a wise investment. Please take a few moments to read these instructions to become familiar with it using.
To guard against injury, basic safety precautions should be observed:
1. This boat cover is NOT intended to be used as a travel cover. It is intended use is to protect your boat from the elements.
2. Tie down cords or straps are not included with the package. Be sure to use, tighten and secure all straps and hooks when transporting your boat on a trailer or open vehicle. Failure to do this may cause the cover to blow off, become damaged or cause injury to others. Our product warranty does not cover any kind of loss or liability in such a situation.
3. Only use soapy water or fresh water to wash the cover. The manufacturer is not responsible for damage caused as a result of improper use or failure to observe these instructions.
4. Keep the product out of the reach of children. There may be a risk of small children choking or suffocating if they become entangled in the cover. Please SAVE this instruction manual.
MODELS: Seamax inflatable boat covers have 6 series. Each series includes a couple of sizes for different tube styles. Those sizes should be the same width. Read the “Model List” below to all our cover sizes. The bow style will not affect the cover size in most cases.
UNIVERSAL COVER: No matter which brand of boat you have, even if it is a RIB with a console, our universal cover should fit as long as your inflatable boat has a built-in transom. If you don't see a listing for your boat's measurements, please contact the seller.
MOTOR WELL DESIGN & TRAILERABLE: Our boat cover should be able to cover your boat and the motor. The covers have been designed to fit the boat and its max rating outboard motor. Fabric Specs - Water repellent, mildew and UV resistant; Density 600D/260g/SQM. Elastic string design for quick fitted and released, Multiple Tie-Down Loops built-in, free cover carrying bag included. Max trailer Road Speed 65km / hour (40mile / hour), additional tie-down core will be required.
A Series – for Boat’s Beam Width Range 4.3 to 4.6 feet
Model & Max Length: A210 – 6.9ft; A240 – 7.9ft; A265 – 8.7ft
B Series - for Boat’s Beam Width Range 4.7 to 5.2 feet
Model & Max Length: B255 – 8.3ft; B270 – 9.0ft; B295 – 9.7ft; B320 – 10.5ft; B350 – 11.5ft
C Series - for Boat’s Beam Width Range 5.3 to 5.7 feet
Model & Max Length: C300 – 9.9ft; C330 – 10.8ft; C360 – 11.8ft; C390 – 12.8ft; C420 – 13.8ft
D Series - for Boat’s Beam Width Range 5.8 to 6.4 feet
Model & Max Length: D370 – 12.2ft; D400 – 13.1ft; D430 – 14ft; D470 – 15.4ft; D500 – 16.5ft
E Series - for Boat’s Beam Width Range 6.6 to 7.2 feet
Model & Max Length: E460 – 15ft; E500 – 16.5ft; E550 – 18ft; E600 – 19.7ft; E680
F Series - for Boat’s Beam Width Range 7.6 to 8.4 feet
Model & Max Length: F550 – 18ft; F600 – 19.7ft; F680 – 22ft; F750 – 24ft
1. Spray down your boat cover with lukewarm water using the nozzle on your garden hose. While the cover is on top of your boat, start at the top and move left to right down the right side. Then repeat on the left. This step should help get rid of the salt or dirt if your boat is exposed to salt water.
2. Take the cover off your boat and lay it open on the ground with the side that's normally exposed to the air face up. Brush the cover with your push broom, starting at the left edge and moving to the right edge. This will remove any remaining large debris. You may need someone to stand on one edge of the cover so it doesn't roll up when you try to brush it.
3. Fill your bucket to the halfway point with water and pour in a quarter cup of a gentle soap. Do not use a detergent, since it can damage your cover's waterproofing. Stir the solution and dip your sponge in it. Use the sponge to dab any areas of your cover that are stained. Let it stand for 10 minutes.
4. Scrub your cover with your scrub brush using a circular motion until all of the stains are removed. If it takes you longer than a half hour, switch from your gentle soap to color-safe bleach, using the same measurements as before.
5. Rinse your boat cover with the hose using the method in Step 1. Let it air dry. If you have any spots on the inside of your cover, flip it over and repeat Steps 1 through 4 to get them off. Do a final rinse. Then let the cover air dry by laying it flat or hanging it over a clothesline. Do NOT put your boat cover in a washing machine or dryer.
6. Store the boat cover in a bag in a clean, dry place. Ensure the cover is completely dry before storing
1. We suggest you remove the cover by folding it to the centre from both sides and rolling the cover from back to front. This may make it easier to repeat the same steps when covering your boat again. (Allow the cover to dry completely before folding for storage)
2. Our boat covers will fit Seamax inflatable boats. And they are also suitable for all major brand names including: Achilles, AB? Avon, Mercury, Seamax, Zodiac, etc. We provide an extra-large carrying bag for your boat cover for storage on selected models.
3. If you are putting your boat & cover on a road trailer, please always use heavy-duty tie down straps (Not included with cover). After driving a short distance and before go on the highway/freeway, stop and check to make sure the boat and cover are secure. Continuing to check the boat and cover frequently along the way is advised.
4. The boat cover support system & tie downs are inexpensive and simple accessories that lengthen the life of your cover. Extra fittings include support poles & straps. (Tie down accessories & support system is not included in the standard package).
Mildew growth on your boat can be damaging, frustrating and hazardous to your health. You can prevent mildew growth by selecting the right boat cover fabric for your climate using a vented support pole to ensure maximum breath ability and by using a boat dryer and or dehumidifier to reduce humidity under the cover. If you do end up with mildew growth on your boat cover, follow these steps to eliminate it: 1). Mix 1 cup of vinegar, 1 cup of borax powder, and 2 cups of warm water in bucket or sprayer. 2). Apply the mixture to mildew spots and let set for no more than 10 minutes. 3). For troublesome spots, use a soft bristle brush and scrub. 4). Rinse well and allow boat cover to dry thoroughly (never use a dryer).
Finally, quality boat covers at a price that makes sense. We should have one or more boat covers that will satisfy your needs. In the meantime, we provide a 2-year limited warranty for the cover. It covers the Fabric structure, sewing lines, tie down string and elastic string.
We guarantee your purchase is brand new. Factory also inspects all shipments to try and make sure there are no missing parts and everything is in new condition. If you find any shipping damage, please contact us with a detailed picture (damaged item and package box) as soon as possible.
We will pay for the 2-way shipping within 30 days of purchase if the purchased item(s) have defects. Customer will pay for the 2-way shipping fee after 90 days when warranty service is required. If you order your boat cover in the wrong size by mistake, you can send it back within 30 days of purchase and additional shipping fee will be applied. you can contact with Seamax for seller support.
Effective design to help water run-off and keep the boat dry. Support pole in the middle to prop boat cover. 4 Straps (one to each corner) to hold the pole in place, form ridges from the pole to corners of the boat, and provide more support for the cover.
Stages Telescopic pole, Height range 22” - 44”; Adjustable Strap max length 9 FT., Pole base diameter: 5-7/8”; all materials suitable for marine environment. Easy to deploy and can be used in many boat cover support scenarios.
Setup Scenario: Set the pole in center of the boat; two straps to connect the back corners D-rings or transom towing rings; two straps to front corners D-rings or front towing rings. Make sure all the strings stay tight, then put the boat cover on.
This boat cover support pole system fits in inflatable boat, aluminum boat, pontoon boat and
fiberglass boat. More than 1 cover support pole system may be needed for a bigger boat.
admin@boardoutlets.com